Codey Online › Arduino- & ESP32-Komponentenbibliothek › GPS NEO-6M
GPS NEO-6M
Sensoren

GPS NEO-6M

Der NEO-6M ist ein GPS-Empfängermodul, das Position, Geschwindigkeit und Zeit aus Satellitensignalen bestimmt. Er kommuniziert typischerweise über UART-Seriell mit einem Mikrocontroller über TX und RX, mit VCC und GND für die Versorgung sowie einem PPS-Pin für eine präzise Zeitausgabe.

Breite: 42.3 mm

Pinbelegung — GPS NEO-6M

Pin Signal Beschreibung
TX TX UART transmit output from the GPS module — connect to the host MCU RX.
GND ground Ground reference for power and UART signals.
VCC power Power input for the GPS module, typically 3.3–5V depending on board regulator.
RX RX UART receive input to the GPS module — connect to the host MCU TX.
PPS digital Pulse-per-second timing output from GPS lock for precise synchronization.

Beispielschaltplan — GPS NEO-6M

Von Nach Kabel
board:5V x1:VCC red
board:GND x1:GND black
board:D4 x1:TX green
board:D3 x1:RX blue

Arduino-Beispielcode — GPS NEO-6M

Dieses Beispiel wurde für das arduino-uno geschrieben und kompiliergeprüft. Codey Online passt es für jedes andere unterstützte Board an.

#include <SoftwareSerial.h>

// GPS NEO-6M canonical example for Arduino Uno
// Wiring:
// GPS VCC -> 5V
// GPS GND -> GND
// GPS TX  -> D4 (Arduino receives on this pin)
// GPS RX  -> D3 (Arduino transmits on this pin)

SoftwareSerial gpsSerial(4, 3); // RX, TX

char lineBuffer[120];
uint8_t lineIndex = 0;

void setup() {
  Serial.begin(9600);
  gpsSerial.begin(9600);

  Serial.println(F("GPS NEO-6M example started."));
  Serial.println(F("Waiting for NMEA sentences..."));
}

void printField(const char *label, const char *value) {
  Serial.print(label);
  Serial.print(value);
}

void handleRMC(char *sentence) {
  // Example: $GPRMC,hhmmss.sss,A,llll.ll,a,yyyyy.yy,a,x.x,x.x,ddmmyy,,,A*hh
  char *fields[12] = {0};
  uint8_t count = 0;
  char *token = strtok(sentence, ",");
  while (token && count < 12) {
    fields[count++] = token;
    token = strtok(NULL, ",");
  }

  if (count < 10) return;
  if (fields[2] == NULL || fields[2][0] != 'A') {
    Serial.println(F("No GPS fix yet."));
    return;
  }

  Serial.println(F("--- Valid Fix (RMC) ---"));
  if (fields[1]) printField("Time (UTC): ", fields[1]), Serial.println();
  if (fields[3] && fields[4]) {
    Serial.print(F("Latitude: "));
    Serial.print(fields[3]);
    Serial.println(fields[4]);
  }
  if (fields[5] && fields[6]) {
    Serial.print(F("Longitude: "));
    Serial.print(fields[5]);
    Serial.println(fields[6]);
  }
  if (fields[7]) {
    Serial.print(F("Speed (knots): "));
    Serial.println(fields[7]);
  }
  if (fields[8]) {
    Serial.print(F("Course (deg): "));
    Serial.println(fields[8]);
  }
  if (fields[9]) {
    Serial.print(F("Date (ddmmyy): "));
    Serial.println(fields[9]);
  }
}

void handleGGA(char *sentence) {
  // Example: $GPGGA,time,lat,N,lon,E,fixquality,numsat,hdop,alt,M,...
  char *fields[15] = {0};
  uint8_t count = 0;
  char *token = strtok(sentence, ",");
  while (token && count < 15) {
    fields[count++] = token;
    token = strtok(NULL, ",");
  }

  if (count < 8) return;
  int fixQuality = fields[6] ? atoi(fields[6]) : 0;
  int satellites = fields[7] ? atoi(fields[7]) : 0;

  Serial.println(F("--- GGA Status ---"));
  Serial.print(F("Fix quality: "));
  Serial.println(fixQuality);
  Serial.print(F("Satellites: "));
  Serial.println(satellites);
  if (fields[8]) {
    Serial.print(F("HDOP: "));
    Serial.println(fields[8]);
  }
  if (fields[9] && fields[10]) {
    Serial.print(F("Altitude: "));
    Serial.print(fields[9]);
    Serial.print(' ');
    Serial.println(fields[10]);
  }
}

void loop() {
  while (gpsSerial.available()) {
    char c = (char)gpsSerial.read();

    if (c == '\n') {
      lineBuffer[lineIndex] = '\0';
      lineIndex = 0;

      // Trim trailing carriage return if present
      char *sentence = lineBuffer;
      size_t len = strlen(sentence);
      if (len > 0 && sentence[len - 1] == '\r') {
        sentence[len - 1] = '\0';
      }

      if (strncmp(sentence, "$GPRMC", 6) == 0 || strncmp(sentence, "$GNRMC", 6) == 0) {
        char temp[120];
        strncpy(temp, sentence, sizeof(temp));
        temp[sizeof(temp) - 1] = '\0';
        handleRMC(temp);
      } else if (strncmp(sentence, "$GPGGA", 6) == 0 || strncmp(sentence, "$GNGGA", 6) == 0) {
        char temp[120];
        strncpy(temp, sentence, sizeof(temp));
        temp[sizeof(temp) - 1] = '\0';
        handleGGA(temp);
      }
    } else {
      if (lineIndex < sizeof(lineBuffer) - 1) {
        lineBuffer[lineIndex++] = c;
      } else {
        lineIndex = 0; // overflow protection
      }
    }
  }
}

Ähnliche Komponenten

18650 Battery Shield with USB-C Charger and 5V Boost Converter

18650 Battery Shield with USB-C Charger and 5V Boost Converter

2.4 inch OLED Display I2C 3.3V

2.4 inch OLED Display I2C 3.3V

3.5 inch TFT LCD Shield

3.5 inch TFT LCD Shield

50kg Load Cell Weight Sensor

50kg Load Cell Weight Sensor

Bau dein Arduino- oder ESP32-Projekt mit AI

Beschreib einfach, was du bauen willst. Codey Online schreibt den Code, zeichnet den Schaltplan, kompiliert alles und flasht dein Board direkt aus dem Browser.

Kostenlos starten