Sensors
18650 Battery Shield with USB-C Charger and 5V Boost Converter
18650 Battery Holder Charging Board, 5V Step-Up Power Bank Module with USB-C Input for Arduino and DIY Electronics
2.4 inch OLED Display I2C 3.3V
This is a 2.4-inch OLED display module intended for use with microcontrollers via the I2C (SDA/SCL) interface. It is des…
3.5 inch TFT LCD Shield
3.5 inch TFT LCD Shield for Arduino UNO and MEGA
50kg Load Cell Weight Sensor
50kg Load Cell Weight Sensor, Electronic Kitchen Scale Strain Gauge
Accelerometer and Gyroscope I2C MPU-6050
The MPU-6050 is an inertial sensor combining a 3-axis accelerometer and a 3-axis gyroscope for measuring motion and orie…
Bosch BME280 3.3v 3-in-1 sensor Temperature Humidity and Air Pressure
The Bosch BME280 is a digital environmental sensor that measures ambient temperature, relative humidity, and barometric …
Bosch BME280 5V 3-in-1 sensor Temperature Humidity and Air Pressure
The Bosch BME280 is a digital environmental sensor that measures temperature, relative humidity, and barometric pressure…
Buzzer module passief Arduino
Buzzer module passief Arduino This passive buzzer emits a sound of approximately 85dB when connected to a voltage betwe…
CAN-bus module MCP2515 SPI 5V
This module is based on the MCP2515 CAN controller, which communicates with a microcontroller over SPI and is used to ad…
DF Player Mini
DF Player Mini Mp3 player with TF Card reader
DHT11 Sensor Module
DHT11 temperature and humidity sensor module
DHT22
The DHT22 is a digital temperature and relative humidity sensor used with microcontrollers. It communicates over a singl…
DS18B20 waterdichte probe temperatuursensor 1 m cable
The DS18B20 is a digital temperature sensor in a waterproof probe housing with a 1 m cable. It communicates over the 1-W…
DS3231 Real Time Clock Module I2C
Real time clock module DS3231 chip I2C
Flame Sensor Module
This module detects the infrared light emitted by flames, making it useful for basic fire detection projects and alarms.…
GPS NEO-6M
The NEO-6M is a GPS receiver module used to determine position, speed, and time from satellite signals. It typically com…
HC-SR04
The HC-SR04 is an ultrasonic distance sensor that measures range by sending a sound pulse and timing the echo return. It…
HC-SR501 PIR Motion Sensor
HC-SR501 Infrared PIR Motion Sensor Module for Arduino and
Human Presence Sensor LD2410C
Human Presence Sensor LD2410C 24GHz
HW-201 Infrared Obstacle Avoidance Module
HW-201 Infrared Obstacle Avoidance Sensor Module, Proximity Switch for Smart Car and Arduino
INMP441 microphone
The INMP441 is a digital MEMS microphone that provides audio data over an I2S interface. Connect SCK as the I2S clock, W…
IR Receiver (VS1838B)
The VS1838B is an IR receiver module that detects modulated infrared remote-control signals and outputs a digital signal…
Keypad 4x4
Keypad with 4x4 buttons 123A 456B 789C *0#D
LDR Light Sensor Module
Photosensitive LDR Light Sensor Module, Photoresistor Detection Board for Arduino and Smart Home
LDR Sensor Module
An LDR (light dependent resistor) sensor module outputs an analog voltage that changes with ambient light intensity. Con…
MAX6675 thermocouple module
The MAX6675 is a thermocouple-to-digital converter module designed for K-type thermocouples. It reads the thermocouple s…
Micro SD Card Adapter Module 3.3V
Micro SD card slot module with SPI interface, 3.3V logic. Accessory board (not a microcontroller); works with ESP32, ESP…
Micro-SD Card Reader 3.3V
This is a 3.3V microSD card reader module that lets a microcontroller communicate with a microSD card over the SPI bus. …
Micro-SD Card Reader 5V
This Micro-SD Card Reader is a SPI interface module for accessing a microSD card as external storage. It connects to a m…
Mini PIR
A Mini PIR (passive infrared) motion sensor detects changes in infrared radiation caused by nearby movement. It is power…
Motion sensor with microwave radar RCWL-051
The RCWL-051 is a microwave radar motion sensor module that detects movement by emitting low-power microwave signals and…
OLED Display 0.96 inch
OLED Display 0.96 inch 128x64 pixels
PIR Sensor HC-SR501
The PIR Sensor HC-SR501 detects changes in infrared (IR) radiation caused by motion, typically from people or animals. I…
PN532 RFID NFC Module
The PN532 RFID/NFC module enables an Arduino/ESP32 to communicate with NFC tags and contactless cards. It typically supp…
RF 433Mhz Receiver Module MX-5V
This is a 433 MHz RF receiver module for receiving low-cost wireless signals, commonly from remote controls and simple s…
RF 433Mhz Transmitter FS1000A
The FS1000A is a low-cost 433 MHz RF transmitter module used for simple wireless data sending, often with Arduino or ESP…
RFID RC522 Module 13.56MHz
The RFID RC522 module (MFRC522 chip) reads and writes RFID/NFC tags operating at 13.56 MHz. It communicates with microco…
Rotary Encoder module
A rotary encoder module converts mechanical rotation into electrical pulses using quadrature (two phase-shifted signals,…
TOF050C-VL6180X Distance Sensor Time-Of-Flight high precision
This TOF module uses the VL6180X time-of-flight distance sensor to measure short-range distances by emitting IR light pu…
TOF200C VL53L0X Distance Sensor Time-Of-Flight high precision
The TOF200C module uses the ST VL53L0X time-of-flight laser ranging sensor to measure distance by timing reflected light…
TOF400C-VL53L1X Distance sensor Time-Of-Flight very accurate 4-400cm
The TOF400C-VL53L1X is a time-of-flight distance sensor module that measures the distance to an object over roughly 4–40…
Touch sensor TTP223B
The TTP223B is a single-channel capacitive touch sensor IC used as a touch-button replacement. It provides a digital tou…
TPA3110 2x15W Amplifier
The TPA3110 is a Class-D stereo audio amplifier module intended to drive two speaker channels. Use the analog left/right…
Water Sensor
A water sensor module detects the presence of water or moisture and provides an analog output on the S pin. Connect GND …
Displays
1.28" Round TFT LCD 240x240 (GC9A01, SPI)
This is a 1.28-inch round TFT LCD module using the GC9A01 controller with a 240x240 pixel resolution. It typically opera…
1602 LCD DISPLAY
A 1602 (16x2) character LCD module typically using an HD44780-compatible controller for displaying alphanumeric text. It…
1602 LCD I2C DISPLAY
1602 I2C display
8x8 RGB 64 LED Matrix 5V WS2812b
An 8x8 (64) RGB LED matrix using WS2812b addressable LEDs for individually controllable pixels. It is typically driven b…
ILI9341 2.8 TFT
This is a 2.8-inch TFT LCD module based on the ILI9341 controller, commonly used to display text, graphics, and simple u…
LCD Display TFT 1.3inch ST7789
LCD Display TFT 1.3inch ST7789 240x240 pixels, 3.3V, SPI, RGB
OLED Display 0.91 inch
128x32 SSD1306
ST7735 TFT 1.8"
This is a 1.8-inch ST7735-based TFT LCD module for displaying text, graphics, and simple UI elements. It typically uses …
TM1637 4-Digit Display
The TM1637 4-Digit Display is a small seven-segment LED module for showing numeric values and simple symbols. It uses a …
Actuators
A4988 Stepper Driver
The A4988 is a stepper motor driver for bipolar stepper motors, using VMOT for the motor power and VDD for the logic sup…
BTS7960 Motor Driver
This BTS7960-based driver module is used to control a DC motor with PWM speed control and separate enable inputs. It exp…
DRV8825 Driver Board
The DRV8825 Driver Board is a stepper motor driver that converts step/direction signals into coil current for two motor …
L298N Motor Driver Board
The L298N Motor Driver Board is a dual H-bridge motor driver that controls two DC motors (direction and speed). Use IN1–…
Left DC Motor
A DC motor converts electrical power into mechanical rotation and is typically used as a left drive motor in mobile robo…
NEMA17 Stepper Motor
A NEMA17 stepper motor converts step pulses into precise angular movement via two electromagnetic coils. It is typically…
Pump 5V
A pump converts electrical power into fluid movement, typically as a small DC load with two power terminals. It is usual…
Servo SG90
The SG90 is a small hobby servo actuator that moves to commanded positions using a PWM control signal. It typically requ…
TB6600 Stepper Driver
The TB6600 is a stepper motor driver that converts STEP (PUL) and DIR (direction) input signals into controlled current …
TB6612FNG Motor Driver
The TB6612FNG is a dual H-bridge motor driver that lets a microcontroller control two DC motors independently. Use PWMA/…
Output
18650 3.7V Li-Ion Battery
A 3.7V Li-Ion battery is a single-cell rechargeable power source commonly used to supply portable electronic projects. I…
3-Channel 5V Relay Module
This is a relay module for controlling external loads from a microcontroller using digital input pins. It is powered fro…
3W amplifier MAX98357A I2S DAC
MAX98357A I2S Class-D mono amplifier breakout (3W). Receives digital I2S audio and drives a speaker directly. No DAC nee…
8-Channel Relay Module
An 8-channel relay module that lets a microcontroller switch eight separate loads using digital control signals. It has …
Active Buzzer Module
Active buzzer. Always use S pin to trigger sound.
LED
Standard 5mm through-hole LED. Available in red, green, blue, yellow, white, orange, and warm white. Requires a current-…
LED Matrix Module MAX7219
This is an LED matrix display module using the MAX7219 LED driver to control a 8x8 LED matrix. It is typically connecte…
Passive Buzzer Module
A passive buzzer module generates sound by converting a digital square-wave (often via PWM) applied to the S control pin…
Relais Module 12v AC250V 10A Relais 12v 1 relais LED indicator
This is a single-channel 12V relay module for switching external loads with a low-voltage control signal. It is rated fo…
Relais Module 5v High load capacity: AC250V 10A / DC30V 10A Relay control: 5V1-channel relay board
This is a 5V single-channel relay module used to switch higher-voltage or higher-current loads with a low-voltage contro…
Relais Module 5v Low
Relais Module 5v Low High load capacity: AC 250V 10A / DC 30V 10A Relay control: 5V Signal: Low trigger1-channel relay b…
Relay module 2-channel 12V
This module contains two electromechanical relays for switching external loads from a low-power microcontroller. It is t…
Relay Module 5V
Relay Module 5V high trigger
WCMCU-5102 module
Stereo I2S DAC module (PCM5102A). Converts digital I2S audio to analog line-level output. Has a 3.5mm headphone jack and…
WS2812 LED Ring 8-bit
Led ring with 8x WS2812 leds
Input & buttons
12V DC power supply
A 12V DC source or supply connection for powering compatible circuits with direct current. It uses two terminals, + and …
5V DC
This is a 5V direct-current power source used to power electronic circuits. It has two terminals, + and -, for connectin…
Drukknop
Knop of button. Kan gebruikt worden voor pulse maar ook voor self-lock.
HX711 Load Cell Amplifier
The HX711 is a dedicated load-cell amplifier that reads strain-gauge bridges and converts the bridge signal into a digit…
Joystick module
This joystick module provides two analog position outputs for the X and Y axes, plus a digital pushbutton switch on SW. …
Keypad 4x3
Keypad 4x3 matrix 123 456 789 *0#
Tactile switch
4-pin momentary tactile push button. Pins 1-2 are connected (left rail), pins 3-4 are connected (right rail). Pressing t…
Communication
CC1101 RF Module
The CC1101 RF Module is a low-power sub-1 GHz RF transceiver module used for wireless data communication. It is typicall…
HC-05 Bluetooth
The HC-05 is a Bluetooth serial module used to add wireless UART communication to microcontroller projects. It connects …
Logic Level Shifter 4-channel
4-channel bidirectional logic level shifter (BSS138-style) that converts between 5V and 3.3V on up to 4 signal lines. Su…
Logic Level Shifter 8-channel
Logic Level Shifter 8-channel to convert 3.3V logic to 5V logic bi-directional
MAX485 TTL to RS485 Converter Module
The MAX485 module is a half-duplex RS-485 transceiver that converts TTL UART signals to a differential RS-485 bus and ba…
NRF24L01
The NRF24L01 is a 2.4 GHz wireless transceiver module for short-range data communication between microcontrollers. It co…
SRX882 RF 433Mhz Receiver
The SRX882 is a 433 MHz RF receiver module for receiving simple wireless data in the 433.92 MHz ISM band. It is typicall…
STX882 433Mhz RF Transmitter
The STX882 is a low-cost 433 MHz RF transmitter module used for simple wireless data links, such as remote controls and …
Interface
16 Channel 12-Bit PWM Servo Driver I2C
16 Channel 12-Bit PWM Servo Driver I2C PCA9685
HW-0519 TTL to RS485 Module
This HW-0519 TTL to RS485 module is a UART-to-RS485 interface board with automatic direction control, used to link a mic…
MCP23017 I/O Expander
The MCP23017 is an I2C-based 16-bit I/O expander that provides two 8-bit GPIO ports (Port A and Port B) for reading digi…
PCM1808 ADC Module
The PCM1808 module is a stereo audio analog-to-digital converter for line-level signals, with left/right analog inputs a…
Active parts
BJT Transistor
Bipolar junction transistor in TO-92 through-hole package. Available as NPN (BC547, 2N3904, BC337, 2N2222 — current flow…
MOSFET Transistor
Power MOSFET in TO-220 through-hole package. Available as N-channel (IRFZ44N, IRF540, IRLZ44N — switches loads to GND, l…
Passive parts
Ceramic Capacitor
Small non-polarized through-hole ceramic disc capacitor. Common values: 10pF, 22pF, 100pF, 1nF, 10nF, 100nF (0.1µF), 1µF…
Diode
Two-terminal polarized semiconductor that conducts current in only one direction (anode → cathode). Common variants: sta…
Electrolytic Capacitor
Polarized aluminium-electrolytic through-hole capacitor in a cylindrical can. Common values: 1µF, 10µF, 47µF, 100µF, 220…
Linear Potentiometer (3-pin)
Through-hole rotary potentiometer with three terminals: both ends of the resistive track plus the wiper (middle pin). Co…
Resistor
1/4W 5% through-hole resistor. Common E24 values: 100, 220, 330, 470, 1k, 2.2k, 4.7k, 10k, 47k, 100k ohm. Used for curre…
Other
4-Channel Optoisolator Board
4-Channel Optocoupler Isolation Module, Voltage Level Converter Board for Arduino and PLC
AD9850 DDS Signal Generator Module
AD9850 DDS (Direct Digital Synthesis) signal generator module. Generates sine and square waves from roughly 0 to 40 MHz …
Adjustable Step-down Module 3-40VDC 1.5-35VDC LM2596
This LM2596-based adjustable buck converter steps down a higher DC input to a lower DC output with good efficiency. It i…
ADS7830 8-Channel 8-Bit ADC
The ADS7830 is an 8-channel, 8-bit analog-to-digital converter designed for reading multiple analog inputs over an I2C i…
Breadboard 400 pin
A 400-point solderless breadboard used to build and test electronic circuits quickly without soldering. It provides mult…
DC 12V adjustable timer delay, time delay relay turn off switch module time relay time switch 0~25sec for smart home, automatic control
This is a DC 12V adjustable delay relay module used for turn-off/interval timing in smart home or automation. The delay …
DC-DC High Power Adjustable Step-up Module 3.0~35V to 3.5~35V 100W with Digital Display Voltmeter
This adjustable DC-DC boost (step-up) module converts a higher-power input supply to a selectable higher voltage range a…
MAX3232 RS232 to TTL Serial Converter Module
MAX3232 RS232 to TTL Serial Port Converter Module, Female DB9 Connector for Arduino and
MT3608 2A Max DC-DC Step Up Power Module Booster Power Module
The MT3608 is a small DC-DC boost (step-up) converter module used to increase an input DC voltage to a higher adjustable…
PWM naar Voltage converter module 0-10V
This module converts a PWM signal into a corresponding analog voltage output, typically in the 0-10V range for control a…
Speaker 3W
Small passive speaker, 3W 4-8 ohm. Requires an amplified signal — cannot be driven directly from a DAC line-out or micro…