Codey Online › Libreria di componenti Arduino ed ESP32 › GPS NEO-6M
GPS NEO-6M
Sensori

GPS NEO-6M

Il NEO-6M è un modulo ricevitore GPS usato per determinare posizione, velocità e ora dai segnali satellitari. Di solito comunica con un microcontrollore tramite UART seriale usando TX e RX, con VCC e GND per l'alimentazione, e un pin PPS per un'uscita temporale precisa.

Larghezza: 42.3 mm

Pinout — GPS NEO-6M

Pin Segnale Descrizione
TX TX UART transmit output from the GPS module — connect to the host MCU RX.
GND ground Ground reference for power and UART signals.
VCC power Power input for the GPS module, typically 3.3–5V depending on board regulator.
RX RX UART receive input to the GPS module — connect to the host MCU TX.
PPS digital Pulse-per-second timing output from GPS lock for precise synchronization.

Schema di cablaggio di esempio — GPS NEO-6M

Da A Filo
board:5V x1:VCC red
board:GND x1:GND black
board:D4 x1:TX green
board:D3 x1:RX blue

Codice Arduino di esempio — GPS NEO-6M

Questo esempio è stato scritto e verificato in compilazione per arduino-uno. Codey Online lo adatta a qualsiasi altra scheda supportata.

#include <SoftwareSerial.h>

// GPS NEO-6M canonical example for Arduino Uno
// Wiring:
// GPS VCC -> 5V
// GPS GND -> GND
// GPS TX  -> D4 (Arduino receives on this pin)
// GPS RX  -> D3 (Arduino transmits on this pin)

SoftwareSerial gpsSerial(4, 3); // RX, TX

char lineBuffer[120];
uint8_t lineIndex = 0;

void setup() {
  Serial.begin(9600);
  gpsSerial.begin(9600);

  Serial.println(F("GPS NEO-6M example started."));
  Serial.println(F("Waiting for NMEA sentences..."));
}

void printField(const char *label, const char *value) {
  Serial.print(label);
  Serial.print(value);
}

void handleRMC(char *sentence) {
  // Example: $GPRMC,hhmmss.sss,A,llll.ll,a,yyyyy.yy,a,x.x,x.x,ddmmyy,,,A*hh
  char *fields[12] = {0};
  uint8_t count = 0;
  char *token = strtok(sentence, ",");
  while (token && count < 12) {
    fields[count++] = token;
    token = strtok(NULL, ",");
  }

  if (count < 10) return;
  if (fields[2] == NULL || fields[2][0] != 'A') {
    Serial.println(F("No GPS fix yet."));
    return;
  }

  Serial.println(F("--- Valid Fix (RMC) ---"));
  if (fields[1]) printField("Time (UTC): ", fields[1]), Serial.println();
  if (fields[3] && fields[4]) {
    Serial.print(F("Latitude: "));
    Serial.print(fields[3]);
    Serial.println(fields[4]);
  }
  if (fields[5] && fields[6]) {
    Serial.print(F("Longitude: "));
    Serial.print(fields[5]);
    Serial.println(fields[6]);
  }
  if (fields[7]) {
    Serial.print(F("Speed (knots): "));
    Serial.println(fields[7]);
  }
  if (fields[8]) {
    Serial.print(F("Course (deg): "));
    Serial.println(fields[8]);
  }
  if (fields[9]) {
    Serial.print(F("Date (ddmmyy): "));
    Serial.println(fields[9]);
  }
}

void handleGGA(char *sentence) {
  // Example: $GPGGA,time,lat,N,lon,E,fixquality,numsat,hdop,alt,M,...
  char *fields[15] = {0};
  uint8_t count = 0;
  char *token = strtok(sentence, ",");
  while (token && count < 15) {
    fields[count++] = token;
    token = strtok(NULL, ",");
  }

  if (count < 8) return;
  int fixQuality = fields[6] ? atoi(fields[6]) : 0;
  int satellites = fields[7] ? atoi(fields[7]) : 0;

  Serial.println(F("--- GGA Status ---"));
  Serial.print(F("Fix quality: "));
  Serial.println(fixQuality);
  Serial.print(F("Satellites: "));
  Serial.println(satellites);
  if (fields[8]) {
    Serial.print(F("HDOP: "));
    Serial.println(fields[8]);
  }
  if (fields[9] && fields[10]) {
    Serial.print(F("Altitude: "));
    Serial.print(fields[9]);
    Serial.print(' ');
    Serial.println(fields[10]);
  }
}

void loop() {
  while (gpsSerial.available()) {
    char c = (char)gpsSerial.read();

    if (c == '\n') {
      lineBuffer[lineIndex] = '\0';
      lineIndex = 0;

      // Trim trailing carriage return if present
      char *sentence = lineBuffer;
      size_t len = strlen(sentence);
      if (len > 0 && sentence[len - 1] == '\r') {
        sentence[len - 1] = '\0';
      }

      if (strncmp(sentence, "$GPRMC", 6) == 0 || strncmp(sentence, "$GNRMC", 6) == 0) {
        char temp[120];
        strncpy(temp, sentence, sizeof(temp));
        temp[sizeof(temp) - 1] = '\0';
        handleRMC(temp);
      } else if (strncmp(sentence, "$GPGGA", 6) == 0 || strncmp(sentence, "$GNGGA", 6) == 0) {
        char temp[120];
        strncpy(temp, sentence, sizeof(temp));
        temp[sizeof(temp) - 1] = '\0';
        handleGGA(temp);
      }
    } else {
      if (lineIndex < sizeof(lineBuffer) - 1) {
        lineBuffer[lineIndex++] = c;
      } else {
        lineIndex = 0; // overflow protection
      }
    }
  }
}

Componenti correlati

18650 Battery Shield with USB-C Charger and 5V Boost Converter

18650 Battery Shield with USB-C Charger and 5V Boost Converter

2.4 inch OLED Display I2C 3.3V

2.4 inch OLED Display I2C 3.3V

3.5 inch TFT LCD Shield

3.5 inch TFT LCD Shield

50kg Load Cell Weight Sensor

50kg Load Cell Weight Sensor

Crea il tuo progetto Arduino o ESP32 con l'AI

Descrivi cosa vuoi realizzare. Codey Online scrive il codice, disegna lo schema di collegamento, lo compila e programma la tua scheda direttamente dal browser.

Inizia gratis